Figures are for the base model. All models in this family are listed below.
A spiral classifier separates solids by settling velocity in a U-shaped trough. Slurry enters at the side, coarse and heavy particles sink and are carried up the incline by the rotating screw, and the fine fraction overflows the weir at the far end. The machine is built from a U-shaped tank, the spiral assembly, the drive and a lifting mechanism.
The overflow weir height decides what the machine can separate. The high-weir type (FG) holds a shallow pool over the weir and cuts at about 0.15 mm and coarser. The submerged type (FC) keeps the screw fully under the pulp, which gives a larger settling area and lets it cut below 0.15 mm. Models with a 2 prefix — 2FG, 2FC — carry two screws side by side in one trough, roughly doubling the return-sand capacity for the same floor length.
Pre-classification, ahead of the mill: pull out the fines that are already small enough so the mill is not grinding them again. Check classification, in closed circuit with a ball mill: this is the main duty, holding the product fineness by returning coarse sand. Desliming and dewatering: washing, removing slimes, or thickening a pulp before the next stage.
Slurry from the mill enters the bottom of the trough at the side. In the calm pool the coarse, heavy particles settle quickly; the fine, light ones stay in suspension. The pulp level rises and the fine fraction overflows the weir as the overflow product and goes to the next stage. The screw turns slowly, pushing the settled coarse sand up the incline and out at the top as return sand, back to the mill for regrinding. A lifting device raises or lowers the screw, which changes the settling area and fine-tunes the cut size.
Read the return-sand figure first: it is the coarse tonnage the screw can lift per day, and it is what ties the classifier to the mill. The overflow figure is the fines leaving the circuit. FG for a cut at 0.15 mm and above, FC below it. Twin-screw models are for high tonnages where a single screw would be too long or too slow.
The drive motor on 2FC-30 and one dimension of its overall size are not given in the source sheet and are marked —. Nominal screw speeds are adjustable on site through the lifting device and the drive. Technical parameters are subject to change without further notice.
| Model | Screw dia. (mm) | Trough length (mm) | Screw speed (r/min) | Return sand (t/d) | Overflow (t/d) | Drive motor (kW) | Lift motor (kW) | Overall size L×W×H (mm) | Weight (t) |
|---|---|---|---|---|---|---|---|---|---|
| FG-7 | 750 | 5500 | 6–10 | 340–570 | 65 | 3 | — | 6720×980×1820 | 3.1 |
| FG-10 | 1000 | 6500 | 5–8 | 675–1080 | 110 | 5.5 | — | 7590×1240×2380 | 4.9 |
| FC-10 | 1000 | 8400 | 5–8 | 675–1080 | 85 | 7.5 | — | 9600×1240×2680 | 6.2 |
| FG-12 | 1200 | 6500 | 4–6 | 1170–1870 | 155 | 7.5 | 2.2 | 8180×1570×3110 | 8.5 |
| FC-12 | 1200 | 8400 | 4–6 | 1170–1870 | 120 | 7.5 | 2.2 | 10370×1540×3920 | 11 |
| 2FG-12 | 1200 | 6500 | 4–6 | 2340–3740 | 310 | 15 | 4.4 | 8230×2790×3110 | 15.8 |
| 2FC-12 | 1200 | 8400 | 4–6 | 2340–3740 | 240 | 15 | 4.4 | 10370×2790×3920 | 17.6 |
| FG-15 | 1500 | 8300 | 4–6 | 1830–2740 | 235 | 7.5 | 2.2 | 10410×1880×4080 | 12.5 |
| FC-15 | 1500 | 10500 | 4–6 | 1830–2740 | 185 | 7.5 | 2.2 | 12670×1820×4890 | 16.8 |
| 2FG-15 | 1500 | 8300 | 4–6 | 2280–5480 | 470 | 15 | 4.4 | 10410×3390×4080 | 22.1 |
| 2FC-15 | 1500 | 10500 | 4–6 | 2280–5480 | 370 | 15 | 4.4 | 12670×3370×4890 | 30.7 |
| FG-20 | 2000 | 8400 | 3.5–5.5 | 3290–5940 | 400 | 11–15 | 3 | 10790×2530×4490 | 20.5 |
| FC-20 | 2000 | 12900 | 3.5–5.5 | 3210–5940 | 320 | 11–15 | 3 | 15610×2530×5340 | 28.5 |
| 2FG-20 | 2000 | 8400 | 3.5–5.5 | 7780–11880 | 800 | 22–30 | 6 | 11000×4600×4490 | 35.5 |
| 2FC-20 | 2000 | 12900 | 3.5–5.5 | 7780–11880 | 640 | 22–30 | 6 | 15760×4600×5640 | 48.7 |
| FG-24 | 2400 | 9130 | 3.67 | 6800 | 580 | 15 | 3 | 11650×2910×4970 | 26.8 |
| FC-24 | 2400 | 14130 | 3.67 | 6800 | 490 | 18.5 | 4 | 16580×2930×7190 | 41 |
| 2FG-24 | 2400 | 9130 | 3.67 | 13600 | 1160 | 30 | 6 | 12710×5430×5690 | 45.8 |
| 2FC-24 | 2400 | 14130 | 3.67 | 13700 | 910 | 37 | 8 | 17710×5430×8000 | 67.9 |
| 2FG-30 | 3000 | 12500 | 3.2 | 23300 | 1785 | 40 | 8 | 16020×6640×6350 | 73 |
| 2FC-30 | 3000 | 14300 | 3.2 | 23300 | 1410 | — | — | 17091×—×8680 | 84.8 |
Swipe the table sideways to see every column →
80–100 t/h Mobile Dry Gold Separator1 models
5–10 t/h Weathered Sand Gold Plant2 models
SF & XJK Series Flotation Machines11 models