Home / Shop / Ore Dressing

XB Series Agitating Vessels

Ore Dressing · XB-500 — XB-3500 · 9 models
XB Series Agitating Vessels

Key figures

  • Tank ID (mm)500
  • Tank height (mm)500
  • Effective volume (m³)0.098
  • Impeller speed (r/min)600

Figures are for the base model. All models in this family are listed below.

Overview

What it is

An agitating vessel mixes slurry before flotation. Reagent is added to the pulp and stirred until it is fully dispersed, so the conditioner and the mineral surfaces have time to react before the pulp reaches the flotation bank. It can also be used as a surge or holding tank between grinding and the next stage.

Where it sits in the circuit

Typically after the mill and classifier, ahead of the flotation bank. Pulp enters at the top, the impeller keeps the solids in suspension, and the conditioned pulp overflows or is pumped to the first cell. Because the tank holds a fixed volume, it also buffers the flow between an intermittently fed mill and a continuously fed flotation bank.

What it handles

Suitable for slurry with density below 30% by weight and particle size below 1 mm. Above that concentration the impeller cannot keep the coarse fraction fully in suspension, and the tank starts to sand up.

Build

The tank is a vertical cylinder with a flat or slightly conical bottom, supported on legs or a skirt. The drive is mounted on a bridge over the top: motor, V-belt or direct coupling, and a shaft running down the centre line to the impeller. Tanks from XB-1200 up carry an inspection opening and a discharge at the bottom.

Choosing a size

Effective volume is quoted per tank, so residence time follows from the throughput: divide the tank volume by the pulp flow to get minutes of conditioning. For reagent addition, 3–5 minutes is usually enough; for pH adjustment or a slow collector, go longer and size up one model. The impeller speed drops as the tank grows — 600 r/min on the XB-500 against 210–230 r/min on the XB-3000 and XB-3500 — because the impeller diameter grows with it.

Notes

Motor frame designations are reproduced as supplied by the series sheet. Technical parameters are subject to change without further notice.

In the workshop

Conditioning tanks in the workshop: drive bridge and motor on top, tank body below, discharge branch at the bottom.
Conditioning tanks in the workshop: drive bridge and motor on top, tank body below, discharge branch at the bottom.

All models

ModelTank ID (mm)Tank height (mm)Effective volume (m³)Impeller speed (r/min)Impeller dia. (mm)Weight (t)Motor modelMotor powerOverall size L×W×H (mm)
XB-5005005000.0986002000.15Y905-61.1 kW600×566×954
XB-7507507500.335302550.6Y90L-41.5 kW1131×880×1241
XB-1000100010000.585302550.99Y90L-41.5 kW1131×1130×1492
XB-1200120012001.43004001.05Y132S-63 kW1500×1480×1800
XB-1500150015002.23204001.2Y132S-63 kW1750×1640×2190
XB-2000200020005.462305501.6Y132M2-65.5 kW2380×2162×2850
XB-25002500250011.22306503.44Y160L-611 kW3036×2716×3543
XB-30003000300019.12107004.16Y225S-818.5 kW3604×3216×4250
XB-350035003500302308507.28Y225M-822 kW3940×3766×5386

Swipe the table sideways to see every column →

Related equipment

80–100 t/h Mobile Dry Gold Separator1 models5–10 t/h Weathered Sand Gold Plant2 modelsSF & XJK Series Flotation Machines11 models
Prices are quoted per project. Tell us the ore type, the target throughput and the site power supply, and we will confirm the configuration and the delivered price.